Hand Feed Portable Hone SAN-815
Ideal for occasional heavy duty honing in ranges from 2.500" I.D., to 21.000" I.D.
Portable Hones Components
| FOR COMPLETE PORTABLE HONE ORDER 1, 2, 3, 4 & 5 |
| Diameter Range |
1
Basic Tool |
2
Master Holder Sets |
3
Stone Support |
4
Stone Set |
5
Shaft Extension |
| General Purpose Stone Sets |
| Inches |
mm |
SAN |
Single Length |
Double Length |
| 2.5 - 5.5 |
64 - 140 |
SAN-815 |
NONE |
NONE |
NONE |
SEE CHART BELOW |
For holes longer
than 9" (SAN-815)
see Shank and
Shaft Extension Table |
| 4.1 - 6.3 |
104 - 160 |
SAN-815 |
SAN-345 |
NONE |
NONE |
| 4.7 - 7.0 |
119 - 178 |
SAN-815 |
SAN-355 |
SAN-855 |
NONE |
| 6.0 - 9.0 |
152 - 229 |
SAN-815 |
SAN-365 |
SAN-865 |
SAN-260 |
| 8.1 - 12.0 |
206 - 305 |
SAN-815 |
SAN-375 |
SAN-875 |
SAN-280 |
| 11.0 - 15.0 |
279 - 381 |
SAN-815 |
SAN-385 |
SAN-885 |
SAN-290 |
| 14.0 - 18.0 |
356 - 457 |
SAN-815 |
SAN-395 |
SAN-895 |
SAN-340 |
| 17.0 - 21.0 |
432 - 533 |
SAN-815 |
SAN-415 |
SAN-915 |
SAN-450 |
master holder sets
Master Holder Sets listed in the table above, are used with Type SW47 Stone Sets. Double Length Master Holders require two stone sets for use when the bore is more than 18" (457mm) long or when it is necessary to bridge interruptions in the bore. Each Master Holder Set consists of two holders for stones and two holders for guides. Stone supports are required to give rigidity to the hone assembly when honing bores larger than 7" (178mm) diameter.
DRIVE SHANKS AND SHAFT EXTENSIONS
Furnished with 3" (76 mm) Drive Shank. Other shanks or extensions may be selected from the table below to make up any practical length (either drive shank can be used with any combination of extensions). |
| Length |
Replacement Drive Shanks |
Shaft Extensions |
| Inches |
mm |
| 3 |
76 |
SAN-608A |
NONE |
| 6 |
152 |
SAN-618A |
SAN-840 |
| 12 |
305 |
NONE |
SAN-841 |
| 24 |
610 |
NONE |
SAN-842 |
| 36 |
914 |
NONE |
SAN-844 |
| 48 |
1219 |
NONE |
|
| 60 |
1524 |
NONE |
NONE |
| 72 |
1829 |
NONE |
NONE |
portable hone stone sets
| portable stone sets |
| MATERIALS |
HOLE DIAMETERS |
| |
2.5" to 2.7"
(64 to 69 mm) |
2.7" to 4.1"
(69 to 104 mm) |
3.5" to 5.5"
(89 to 140 mm) |
4.1" to 21"
(104 to 533 mm) |
| Deburring In Rough Holes |
| All Materials |
SG25-A47 |
SM27-A47 |
SN37-A47 |
SW47-A47 |
| Fast Stock Removal, in Deburred, Bored, Ground or Reamed Holes |
| Aluminum |
SG25-J45 |
SM27-J45 |
SN37-J45 |
SW47-J45 |
| Brass, Soft |
SG25-J63 |
SM27-J63 |
SN37-J63 |
SW47-J63 |
| Bronze |
SG25-J45 |
SM27-J45 |
SN37-J45 |
SW47-J45 |
| *Carbide |
SG25-DM45 |
SM27-DM45 |
SN37-DM45 |
SW47-DM45 |
| Cast Iron |
SG25-J45 |
SM27-J45 |
SN37-J45 |
SW47-J45 |
| *Ceramic |
SG25-DM45 |
SM27-DM45 |
SN37-DM45 |
SW47-DM45 |
| *Glass |
SG25-DM45 |
SM27-DM45 |
SN37-DM45 |
SW47-DM45 |
| Steel, Soft |
SG25-A45 |
SM27-A45 |
SN37-A45 |
SW47-A45 |
Steel, Hardened
(try this stone first) |
SG25-A45 |
SM27-A45 |
SN37-A45 |
SW47-A45 |
Steel, Hardened
(if A45 does not cut) |
SG25-A43 |
SM27-A43 |
SN37-A43 |
SW47-A43 |
Steel, Very Hard Tool
(if A43 does not cut)* |
SG25-J63 |
SM27-J63 |
SN37-J63 |
SW47-J63 |
| Fine Finishing in Previous Honed Holes |
| Aluminum |
SG25-J87 |
SM27-J87 |
SN37-J87 |
SW47-J87 |
| Brass, Soft |
SG25-J85 |
SM27-J85 |
SN37-J85 |
SW47-J85 |
| Bronze |
SG25-J87 |
SM27-J87 |
SN37-J87 |
SW47-J87 |
| *Carbide |
SG25-DM85 |
SM27-DM85 |
SN37-DM85 |
SW47-DM85 |
| Cast Iron |
SG25-J87 |
SM27-J87 |
SN37-J87 |
SW47-J87 |
| *Ceramic |
SG25-DM87 |
SM27-DM87 |
SN37-DM87 |
SW47-DM87 |
| *Glass |
SG25-DM87 |
SM27-DM87 |
SN37-DM87 |
SW47-DM87 |
| Steel, Hard |
SG25-J85 |
SM27-J85 |
SN37-J85 |
SW47-J85 |
| Steel, Soft |
SG25-J87 |
SM27-J87 |
SN37-J87 |
SW47-J87 |
| *These DIAMOND and CBN SUPERABRASIVE honing sets are all SPECIAL ORDER. They are NOT RETURNABLE except for a manufacturing defect. Please contact us prior to placing order if you have any questions. 800.346.6399 |